Skip to main content

Sigenergy specs checked 13 November 2026

Sigenergy Installer for Hertfordshire and North London

Sola UK installs and commissions Sigenergy SigenStor home battery systems from our base in St Albans. This page is for homeowners in Hertfordshire, North London and the Buckinghamshire fringe who want to keep more of their own solar power, stay powered through a power cut, or charge an EV from the same system.

A SigenStor is built from modules. Each SigenStor BAT 6.0 holds 6.02 kWh, each SigenStor BAT 10.0 holds 9.04 kWh, and one Sigen Energy Controller takes up to six of them, so a system can start small and grow. We are MCS certified for battery storage as well as solar PV (certificate IAA-10034, registered as Sola Renewable Company Limited), and if a battery doesn't suit the way you use electricity, we'll tell you so at survey.

Get a Sigenergy quote

Tell us where you are and we will arrange a free survey. No obligation.

What's in a Sigenergy system

Sigenergy calls SigenStor a 5-in-One system: one stack that combines a solar inverter, a battery inverter, the battery packs, an energy management system and, if you add it, an EV DC charger. Your installation is built from these parts:

  • Sigen Energy Controller (SigenStor EC). The hybrid inverter at the top of the stack. It takes your solar panels and runs the system. Single-phase models run from 3.0 to 12.0 kW and three-phase models from 5.0 to 30.0 kW.
  • Sigen Battery modules (SigenStor BAT). Lithium iron phosphate (LFP) packs that stack beneath the controller, one to six per controller.
  • Sigen Energy Gateway. Switches your home to battery power in a power cut. You only need it if you want backup.
  • Sigen EV DC Charging Module (SigenStor EVDC). An optional module that charges an EV directly from the stack.
  • mySigen App. Monitoring and control for you, and the commissioning tool for us.

Sigenergy components at a glance

Part (Sigenergy's name)What it doesKey figures
Sigen Energy Controller, single phase (SigenStor EC 3.0 SP to 12.0 SP)Hybrid inverter and energy management3.0, 3.6, 4.0, 4.6, 5.0, 6.0, 8.0, 10.0 or 12.0 kW. IP66
Sigen Energy Controller, three phase (SigenStor EC 5.0 TP to 30.0 TP)The same, for three-phase supplies5.0 to 30.0 kW. IP66
Sigen Battery (SigenStor BAT 6.0 / BAT 10.0)Stackable LFP storage6.02 / 9.04 kWh total; 5.84 / 8.76 kWh usable. 3.0 / 4.6 kW charge and discharge. IP66. Floor-standing or wall-mounted
Sigen Energy Gateway (HomePro SP / SP-F / TP)Backup switchover and generator input12 / 22 / 30 kW. 0 ms load-side disruption (Sigenergy test conditions). IP55. Wall-mounted
Sigen EV DC Charging Module (SigenStor EVDC 12 / 25)DC EV charging from the stack12.5 / 25 kW. CCS2 connector. IP66. V2X-ready, subject to the car
Sigen EV AC Charger (Sigen EVAC 7 / 11 / 22)Wall-mounted AC charger7 kW single phase; 11 or 22 kW three phase. Type 2

Figures from Sigenergy's product page, European warranty and Home Energy Solution brochure, checked 13 November 2026.

Battery sizes: what a home system can hold

Sigenergy's current modules come in two sizes, and one name catches people out: the SigenStor BAT 10.0 holds 9.04 kWh, not 10. Usable capacity is a little lower than the total, as the table shows.

Modules on one controllerSigenStor BAT 6.0: total (usable)SigenStor BAT 10.0: total (usable)
16.02 kWh (5.84 kWh)9.04 kWh (8.76 kWh)
212.04 kWh (11.68 kWh)18.08 kWh (17.52 kWh)
318.06 kWh (17.52 kWh)27.12 kWh (26.28 kWh)
424.08 kWh (23.36 kWh)36.16 kWh (35.04 kWh)
530.10 kWh (29.20 kWh)45.20 kWh (43.80 kWh)
636.12 kWh (35.04 kWh)54.24 kWh (52.56 kWh)

Calculated from Sigenergy's per-module figures.

The first-generation SigenStor BAT 5.0 (5.38 kWh) and BAT 8.0 (8.06 kWh) are still covered by the same warranty. Sigenergy fits a DC-DC optimiser in every pack, so new and older modules can work side by side and a system can be extended rather than replaced. More modules add storage. How fast the battery charges and discharges depends on the module count (3.0 kW per BAT 6.0, 4.6 kW per BAT 10.0) and on the controller's rating.

Backup power in a power cut

A Sigenergy battery only runs your home through a power cut if a Sigen Energy Gateway is fitted. With the Gateway, controller and battery working together, Sigenergy rates the load-side disruption at 0 ms, so your lights and router shouldn't notice the switch. That rating assumes the controller's power is greater than the load it is supporting.

That assumption is what decides between whole-home and partial backup. A 6.0 kW single-phase controller delivers 6 kW continuously, so an electric shower, an oven and an EV charger running together could exceed it. We agree at survey which circuits stay on. In the mySigen App you set a Backup Reserve, which is a share of the battery held back for outages. The Gateway can also take a generator for longer cuts.

Charging an EV from the same system

Sigenergy offers two routes. The Sigen EV DC Charging Module stacks onto the SigenStor and charges through a CCS2 connector at up to 12.5 kW or 25 kW, depending on the model. It draws on solar, battery and grid together, so the rate at any moment depends on what those sources can supply. It is built for vehicle-to-home and vehicle-to-grid use, but Sigenergy is clear that V2X depends on your car and on standards still being published, with support to follow by software update. Under the network rules (EREC G98), an EV that exports to the grid counts as electricity storage, so it would form part of your grid application.

The Sigen EV AC Charger is a conventional wall charger: 7 kW on a single-phase supply, or 11 or 22 kW on three-phase, with a Type 2 connection. Paired with a SigenStor it can charge from surplus solar. For the chargers we fit, see our EV charger installation page.

The mySigen App and smart tariffs

The mySigen App shows live energy flow, history and battery state, and it is where you set the system's operating mode. Three modes matter on a UK tariff:

  • Sigen AI Mode uses local peak and off-peak prices, weather and your household's usage pattern to plan when the battery charges and discharges.
  • Time-based Control Mode lets you set the charge, discharge and self-consumption windows yourself, up to 24 periods, which suits a fixed time-of-use tariff.
  • Self-Consumption Mode runs the house on solar first, charges the battery with the surplus and exports only what is left.

Sigenergy updates the app regularly. Recent versions added solar, usage and battery forecasts, local access for diagnostics when the internet is down, and (in October 2026) tariff recommendations for UK users. What a battery is worth to you depends on your tariff and how you use electricity, so we work that through with you at survey rather than quoting a figure here.

The Sigenergy warranty, in plain terms

Sigenergy's current European warranty for SigenStor sets these terms:

Sigenergy partProduct warrantyWhat else applies
Sigen Battery (SigenStor BAT 5.0, 6.0, 8.0, 10.0)10 yearsKeeps at least 60% of usable energy for 10 years or up to a minimum throughput, whichever comes first: 18.20 MWh (BAT 5.0), 20.44 MWh (BAT 6.0), 27.30 MWh (BAT 8.0), 30.66 MWh (BAT 10.0)
Sigen Energy Controller (SigenStor EC) and SigenStor BC10 yearsThe system must stay connected to the internet (below)
Sigen Energy Gateway5 yearsUnder Sigenergy's separate inverter-system warranty
Sigen EV DC Charging Module3 yearsNone
Light strips in the decorative cover2 yearsNone

Source: Sigenergy Factory Limited Warranty for SigenStor (For Europe), read on sigenergy.com on 13 November 2026.

Each throughput figure equals 3,500 full cycles of that module's usable capacity. A battery cycled fully once a day would reach it in about nine and a half years. One that charges twice a day, from solar and from a cheap overnight rate, would reach it sooner.

One condition is worth knowing before you buy: to keep the 10-year warranty, the system has to stay connected to the internet for firmware updates. After 90 days offline it goes into a Safe Operation Mode, and a long disconnection can reduce the cover. Our own workmanship guarantee is separate from Sigenergy's warranty.

Safety and where it can go

Sigenergy uses LFP cells, rated by the cell maker at 10,000 cycles under test conditions. It lists five layers of battery protection: cell-level temperature monitoring, an internal fire-extinguishing kit, high-temperature insulating pads, aerogel insulating pads and a decompression valve. The controller and modules are rated IP66 and can stand on the floor or hang on a wall, indoors or outdoors. The batteries operate from -20 °C to 55 °C, and Sigenergy recommends 10 to 30 °C for the longest life. A ventilated garage or a sheltered outside wall usually works well. In a garage we keep the stack out of the car's path.

Why we recommend Sigenergy

  • It grows with you. Start with one module and add more later, up to six per controller, without replacing what you have.
  • Backup without a flicker. With the Gateway, the switchover is rated at 0 ms on the load side, and you choose whole-home or priority circuits.
  • Fewer boxes on the wall. The solar inverter, battery inverter and energy management share one stack, with EV charging as an option.
  • An app that does real work. Forecasts, Sigen AI Mode and UK tariff recommendations in one place.

We also fit the Tesla Powerwall 3, and we'll recommend whichever suits your home.

How a Sola Sigenergy installation works

  1. Survey. We check your supply (single or three phase), your consumer unit, where the stack can go and, if you have solar, the existing inverter.
  2. Design and quote. We size the controller and modules to your usage, solar and tariff, agree backup and EV charging, and give you a written quote that names every Sigenergy model. Our solar quote checklist shows what a quote should contain.
  3. Network application. If your battery inverter plus any solar inverter comes to more than 16 A per phase (3.68 kW on a single-phase supply), we apply to the network operator under G99 and wait for approval before connecting. Across Hertfordshire and North London that operator is UK Power Networks. Smaller systems are notified under G98 after commissioning. Our guide to G98, G99 and SGI applications explains the routes.
  4. Installation. We fit the stack, the Gateway if you are having backup, and any new panels.
  5. Commissioning and MCS. We commission the system in the mySigen App, register the installation with MCS and give you the certificate.
  6. Handover. We set your operating mode and Backup Reserve with you, connect your app and hand over the documents you should keep.

Adding a Sigenergy battery to existing solar

You don't need new panels to add a Sigenergy battery. Your existing solar inverter keeps working, and the SigenStor is installed alongside it. A Sigen Power Sensor at the grid connection point measures what the house imports and exports, so the battery can store surplus solar. If you are adding panels at the same time, the Sigen Energy Controller can take the new strings directly.

Before you go ahead, check three things:

  • The network application. The battery inverter's output is added to your existing inverter's, so many retrofits go over 3.68 kW on a single-phase supply and need G99 approval first.
  • VAT. A battery retrofitted to solar in a home is zero-rated until 31 March 2027. From 1 April 2027 the rate is 5% (HMRC VAT Notice 708/6).
  • Backup. If you want power-cut cover, plan the Gateway now, because it is wired in between your incoming supply and the circuits it protects.

A Sigenergy system we've fitted

Sigenergy SigenStor battery stack installed by Sola UK
A Sigenergy SigenStor battery stack fitted by Sola UK.

Sigenergy questions we're asked

Is Sola an official Sigenergy installer?

We install and commission Sigenergy systems, and our MCS certification covers battery storage as well as solar PV (certificate IAA-10034, registered as Sola Renewable Company Limited). You can check it in the MCS installer directory. Sigenergy keeps its own map of registered installers.

How big a Sigenergy battery do I need?

Enough to cover what you use between the end of the solar day and your next cheap or sunny period, and not much more. Each SigenStor BAT 6.0 adds 5.84 kWh of usable storage and each BAT 10.0 adds 8.76 kWh. We size from your actual usage, solar output and tariff, because capacity that never gets used is capacity you've paid for.

Can I add more Sigenergy batteries later?

Yes, up to six modules per Sigen Energy Controller. Sigenergy puts a DC-DC optimiser in each pack, so a new module can work alongside older ones. Extra modules add storage, but the controller's rating still caps how much power the system delivers at once.

Will a Sigenergy battery keep my power on in a power cut?

Only if a Sigen Energy Gateway is fitted. With it, Sigenergy rates the switchover at 0 ms on the load side, under its own test conditions, and you can back up the whole home or chosen circuits. How long the power lasts depends on the charge held in your Backup Reserve and on what you run.

Can a Sigenergy battery go outside?

Yes. The controller and battery modules are rated IP66, and they can stand on the floor or hang on a wall, indoors or outdoors. The batteries operate from -20 °C to 55 °C, with 10 to 30 °C recommended for the longest life, so a sheltered wall or a ventilated garage is usually the best spot.

How long is the Sigenergy warranty?

Under Sigenergy's European terms it is ten years on the battery modules and the controller, five years on the Gateway and three on the EV DC Charging Module. The battery is warranted to keep at least 60% of its usable energy for ten years or up to a set throughput, whichever comes first, and the system must stay connected to the internet.

Is there VAT on a Sigenergy battery?

Not until 31 March 2027. Under HMRC's energy-saving materials relief, batteries installed in homes have been zero-rated since 1 February 2024, including batteries added to existing solar and standalone batteries. From 1 April 2027 the rate becomes 5%.

Do I need the network operator's permission?

Usually, yes. If your battery inverter plus any solar inverter comes to more than 16 A per phase, which is 3.68 kW on a single-phase supply, the network operator has to approve the connection under G99 before we connect it. We prepare and submit the application. Smaller systems are notified under G98 after commissioning.

Where we install Sigenergy

We install Sigenergy systems across Hertfordshire, North London and the Buckinghamshire fringe from our St Albans base. If your postcode is outside that area, send it anyway and we'll tell you plainly whether we can reach you. See all the areas we cover or home battery storage near you, call 0800 470 0922, or ask for a Sigenergy quote.

Get Your Free Solar Panel Quote

Fill in the form below for a free, no-obligation solar survey. Our Hertfordshire team will get back to you within 24 hours.

By submitting this form, you agree to our privacy policy. We never share your data.

St Albans Contact Information

  • Head Office & Showroom

    Arquen House, 4–6 Spicer St,
    St Albans, AL3 4PQ

  • Phone

    0800 470 0922

    Mon-Fri: 8am - 6pm

  • Email

    sales@sola-uk.com

Opening Hours

Monday - Friday08:00 - 18:00
Saturday09:00 - 16:00
SundayClosed